Your Dell Precision™ 670 Computer

Dell Precision™ Workstation 470 and 670 Computers User's Guide

Front View

1

drive door

Open the drive door to access the optional floppy drive and CD/DVD drives.

2

hard-drive light

The hard-drive light is on when the computer reads data from or writes data to the hard drive. The light might also be on when a device such as your CD player is operating.

3

power button

Press this button to turn on the computer.

NOTICE: To avoid losing data, do not use the power button to turn off the computer. Instead, perform a Microsoft® Windows® shutdown.

4

power light

The power light illuminates and blinks or remains solid to indicate different states:

No light — The computer is turned off.
Steady green — The computer is in a normal operating state.
Blinking green — The computer is in a power-saving state.
Blinking or solid yellow — See "Power Problems."

To exit from a power-saving state, press the power button or use the keyboard or the mouse if it is configured as a wake device in the Windows Device Manager. For more information about sleep states and exiting from a power-saving state, see "Power Management."

See "Diagnostic Lights" for a description of light codes that can help you troubleshoot problems with your computer.

5

front-panel door

Open the door to use the front-panel connectors and view the diagnostic lights.

Front View (Doors Open)

1

floppy drive (optional)

Access the optional floppy drive.

2

headphone connector

Attach headphones.

3

microphone connector

Attach a microphone.

4

USB 2.0 connectors (2)

Use the front USB connectors for devices that you connect occasionally, such as flash memory key or cameras, or for bootable USB devices (see "System Setup" for more information on booting to a USB device).

It is recommended that you use the back USB connectors for devices that typically remain connected, such as printers and keyboards.

5

IEEE 1394a connector

Attach high-speed serial multimedia devices, such as a digital video camera.

6

diagnostic lights (4)

Use the lights to help you troubleshoot a computer problem based on the diagnostic code. For more information, see "Diagnostic Lights."

7

externally accessible drives

Access additional drives, such as a CD or DVD drive. Drive arrangement varies on computer configuration.

Opening the Drive Door

Back View

1

cover latch release

To open the computer, lay the computer on its side with the cover latch release at the top and then push the latch to the left. See "Opening the Computer Cover."

2

security cable slot

Use a security cable with the slot to help secure your computer.

3

padlock ring

Insert a padlock to lock the computer cover.

4

power connector

Insert the power cable.

5

card slots

Access connectors for any installed cards.

6

back panel connectors

Plug serial, USB, and other devices into the appropriate connectors.

1

parallel connector

Connect a parallel device, such as a printer, to the parallel connector. If you have a USB printer, plug it into a USB connector.

NOTE: The integrated parallel connector is automatically disabled if the computer detects an installed card containing a parallel connector configured to the same address. For more information, see "System Setup Options."

2

line-out connector

Use the green line-out connector to attach headphones and most speakers with integrated amplifiers.

On computers with a sound card, use the connector on the card.

3

line-in connector

Use the blue line-in connector to attach a record/playback device such as a cassette player, CD player, or VCR.

On computers with a sound card, use the connector on the card.

4

mouse connector

Plug a standard mouse into the green mouse connector. Turn off the computer and any attached devices before you connect a mouse to the computer. If you have a USB mouse, plug it into a USB connector.

If your computer is running the Microsoft Windows XP operating system, the necessary mouse drivers have been installed on your hard drive.

5

USB 2.0 connectors (4)

Use the back USB connectors for devices that typically remain connected, such as printers and keyboards.

It is recommended that you use the front USB connectors for devices that you connect occasionally, such as flash memory key or cameras, or for bootable USB devices.

6

link integrity light

Green — A good connection exists between a 10-Mbps network and the computer.
Orange — A good connection exists between a 100-Mbps network and the computer.
Yellow — A good connection exists between a 1000-Mbps (or 1-Gbps) network and the computer.
Off — The computer is not detecting a physical connection to the network.

7

network adapter connector

To attach your computer to a network or broadband device, connect one end of a network cable to either a network jack or your network or broadband device. Connect the other end of the network cable to the network adapter connector on your computer. A click indicates that the network cable has been securely attached.

NOTE: Do not plug a telephone cable into the network connector.

On computers with a network connector card, use the connector on the card.

It is recommended that you use Category 5 wiring and connectors for your network. If you must use Category 3 wiring, force the network speed to 10 Mbps to ensure reliable operation.

8

network activity light

Flashes a yellow light when the computer is transmitting or receiving network data. A high volume of network traffic may make this light appear to be in a steady "on" state.

9

USB 2.0 connectors (2)

Use the back USB connectors for devices that typically remain connected, such as printers and keyboards.

It is recommended that you use the front USB connectors for devices that you connect occasionally, such as flash memory key or cameras, or for bootable USB devices.

10

IEEE 1394a connector

Attach high-speed serial multimedia devices, such as a digital video camera.

11

keyboard connector

If you have a standard keyboard, plug it into the purple keyboard connector. If you have a USB keyboard, plug it into a USB connector.

12

microphone connector

Use the pink microphone connector to attach a personal computer microphone for voice or musical input into a sound or telephony program.

On computers with a sound card, the microphone connector is on the card.

13, 14

serial connectors

Connect a serial device, such as a handheld device, to the serial port. The default designations are COM1 for serial connector 1 and COM2 for serial connector 2.

For more information, see "System Setup Options."

Inside Your Computer

CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.

1

floppy drive (optional)

2

CD/DVD drive

3

hard drive shroud

4

card cage/video fan

5

power supply

6

processor shroud/fan

7

system board

Cable Colors

Device

Color

Hard drive

Blue cables

Floppy drive (optional)

Black pull-tab

CD/DVD drive

Orange pull-tab

I/O panel

Yellow pull-tab

Device	Color
Hard drive	Blue cables
Floppy drive (optional)	Black pull-tab
CD/DVD drive	Orange pull-tab
I/O panel	Yellow pull-tab

System Board Components

1

front-panel connector (PANEL)

17

PCI Express x16 connector

2

SATA connectors (2) (SATA_0 and SATA_1)

18

processor (CPU_0)

3

battery socket (BATTERY)

19

front-panel audio cable connector (FRONTAUDIO)

4

CD/DVD drive connector (IDE1)

20

processor (CPU_1)

5

CD/DVD drive connector (IDE2)

21

CD-drive audio cable connector (CD_IN)

6

power connector (POWER_2)

22

processor fan connector (FAN_P0)

7

standby power light (AUX_PWR)

23

processor fan connector (FAN_P1)

8

power connector (POWER_1)

24

memory module connector (DIMM _1)

The connectors are labeled DIMM_1 through DIMM_6 with DIMM_1 at the edge of the board. See "Memory Overview" for instructions on installing memory.

9

IEEE 1394a connector (FP1394a)

25

memory module connector (DIMM_6)

The connectors are labeled DIMM_1 through DIMM_6 with DIMM_6 closest to the processor. See "Memory Overview" for instructions on installing memory.

10

card fan connector (FAN_CCAG)

26

Voltage Regulator Module (VRM)

11

SCSI connector (SCSI)

27

suspend-to-RAM light (STR_LED)

12

auxiliary hard-drive activity light connector (AUX_LED)

28

memory fan connector (FAN_MEM)

13

PCIX card connectors

29

password jumper (PSWD)

14

telephony connector (MODEM)

30

RTC reset jumper (RTCRST)

15

PCI Express x8 connector (runs at x4 only)

31

floppy-drive connector (DISKETTE)

16

PCI connector

Back to Contents Page

1	floppy drive (optional)	Access the optional floppy drive.
2	headphone connector	Attach headphones.
3	microphone connector	Attach a microphone.
4	USB 2.0 connectors (2)	Use the front USB connectors for devices that you connect occasionally, such as flash memory key or cameras, or for bootable USB devices (see "System Setup" for more information on booting to a USB device). It is recommended that you use the back USB connectors for devices that typically remain connected, such as printers and keyboards.
5	IEEE 1394a connector	Attach high-speed serial multimedia devices, such as a digital video camera.
6	diagnostic lights (4)	Use the lights to help you troubleshoot a computer problem based on the diagnostic code. For more information, see "Diagnostic Lights."
7	externally accessible drives	Access additional drives, such as a CD or DVD drive. Drive arrangement varies on computer configuration.

1	cover latch release	To open the computer, lay the computer on its side with the cover latch release at the top and then push the latch to the left. See "Opening the Computer Cover."
2	security cable slot	Use a security cable with the slot to help secure your computer.
3	padlock ring	Insert a padlock to lock the computer cover.
4	power connector	Insert the power cable.
5	card slots	Access connectors for any installed cards.
6	back panel connectors	Plug serial, USB, and other devices into the appropriate connectors.

1	parallel connector	Connect a parallel device, such as a printer, to the parallel connector. If you have a USB printer, plug it into a USB connector. NOTE: The integrated parallel connector is automatically disabled if the computer detects an installed card containing a parallel connector configured to the same address. For more information, see "System Setup Options."
2	line-out connector	Use the green line-out connector to attach headphones and most speakers with integrated amplifiers. On computers with a sound card, use the connector on the card.
3	line-in connector	Use the blue line-in connector to attach a record/playback device such as a cassette player, CD player, or VCR. On computers with a sound card, use the connector on the card.
4	mouse connector	Plug a standard mouse into the green mouse connector. Turn off the computer and any attached devices before you connect a mouse to the computer. If you have a USB mouse, plug it into a USB connector. If your computer is running the Microsoft Windows XP operating system, the necessary mouse drivers have been installed on your hard drive.
5	USB 2.0 connectors (4)	Use the back USB connectors for devices that typically remain connected, such as printers and keyboards. It is recommended that you use the front USB connectors for devices that you connect occasionally, such as flash memory key or cameras, or for bootable USB devices.
6	link integrity light	Green — A good connection exists between a 10-Mbps network and the computer. Orange — A good connection exists between a 100-Mbps network and the computer. Yellow — A good connection exists between a 1000-Mbps (or 1-Gbps) network and the computer. Off — The computer is not detecting a physical connection to the network.
7	network adapter connector	To attach your computer to a network or broadband device, connect one end of a network cable to either a network jack or your network or broadband device. Connect the other end of the network cable to the network adapter connector on your computer. A click indicates that the network cable has been securely attached. NOTE: Do not plug a telephone cable into the network connector. On computers with a network connector card, use the connector on the card. It is recommended that you use Category 5 wiring and connectors for your network. If you must use Category 3 wiring, force the network speed to 10 Mbps to ensure reliable operation.
8	network activity light	Flashes a yellow light when the computer is transmitting or receiving network data. A high volume of network traffic may make this light appear to be in a steady "on" state.
9	USB 2.0 connectors (2)	Use the back USB connectors for devices that typically remain connected, such as printers and keyboards. It is recommended that you use the front USB connectors for devices that you connect occasionally, such as flash memory key or cameras, or for bootable USB devices.
10	IEEE 1394a connector	Attach high-speed serial multimedia devices, such as a digital video camera.
11	keyboard connector	If you have a standard keyboard, plug it into the purple keyboard connector. If you have a USB keyboard, plug it into a USB connector.
12	microphone connector	Use the pink microphone connector to attach a personal computer microphone for voice or musical input into a sound or telephony program. On computers with a sound card, the microphone connector is on the card.
13, 14	serial connectors	Connect a serial device, such as a handheld device, to the serial port. The default designations are COM1 for serial connector 1 and COM2 for serial connector 2. For more information, see "System Setup Options."

1	floppy drive (optional)
2	CD/DVD drive
3	hard drive shroud
4	card cage/video fan
5	power supply
6	processor shroud/fan
7	system board

1	front-panel connector (PANEL)	17	PCI Express x16 connector
2	SATA connectors (2) (SATA_0 and SATA_1)	18	processor (CPU_0)
3	battery socket (BATTERY)	19	front-panel audio cable connector (FRONTAUDIO)
4	CD/DVD drive connector (IDE1)	20	processor (CPU_1)
5	CD/DVD drive connector (IDE2)	21	CD-drive audio cable connector (CD_IN)
6	power connector (POWER_2)	22	processor fan connector (FAN_P0)
7	standby power light (AUX_PWR)	23	processor fan connector (FAN_P1)
8	power connector (POWER_1)	24	memory module connector (DIMM _1) The connectors are labeled DIMM_1 through DIMM_6 with DIMM_1 at the edge of the board. See "Memory Overview" for instructions on installing memory.
9	IEEE 1394a connector (FP1394a)	25	memory module connector (DIMM_6) The connectors are labeled DIMM_1 through DIMM_6 with DIMM_6 closest to the processor. See "Memory Overview" for instructions on installing memory.
10	card fan connector (FAN_CCAG)	26	Voltage Regulator Module (VRM)
11	SCSI connector (SCSI)	27	suspend-to-RAM light (STR_LED)
12	auxiliary hard-drive activity light connector (AUX_LED)	28	memory fan connector (FAN_MEM)
13	PCIX card connectors	29	password jumper (PSWD)
14	telephony connector (MODEM)	30	RTC reset jumper (RTCRST)
15	PCI Express x8 connector (runs at x4 only)	31	floppy-drive connector (DISKETTE)
16	PCI connector